#nickelcoppersandwich #400antbms #mobiltyscooterbatterybuild so sound effects free download
By fpvfreaky
0 Downloads
1 months ago
50 seconds
About #nickelcoppersandwich #400antbms #mobiltyscooterbatterybuild so Mp3 Sound Effect
#nickelcoppersandwich #400antbms #mobiltyscooterbatterybuild so I have just got my copper for my nickel copper sandwich ready for Spot 👌 welding that to my 87.4 V battery. I have got an ant BMS 400 A capability and 1000 A 10 second burst. 1. Battery pack (24s12p ANR26650M1b) * Individual Cell Capacity: ANR26650M1b cells have a maximum continuous discharge current rating of either 50A or 70A, depending on the datasheet consulted. For safety, the lower value of 50A is used. * Parallel Configuration (12p): In a parallel configuration, the current capacity of individual cells adds up. Therefore, 12 cells * 50A/cell = 600A continuous discharge. * Series Configuration (24s): The series configuration affects the voltage (24 cells * 3.3V/cell = 79.2V nominal), but it doesn't change the overall current capacity of the parallel strings. * Conclusion: The 24s12p ANR26650M1b battery pack can supply up to 600A continuously. 2. BMS (ANT24HE6-24s-400A) * Continuous Discharge Current: The BMS has a maximum continuous discharge current rating of 400A. * Peak Discharge Current: The BMS also has a peak discharge current rating of 400A. * Conclusion: The BMS limits the continuous current for the entire battery system to 400A. 3. Main power cables (6 AWG) * Ampacity of 6 AWG wire: The ampacity of 6 AWG copper wire depends on the insulation temperature rating: * 60°C insulation: 55 Amps. * 75°C insulation: 65 Amps. * 90°C insulation: 75 Amps. * Important Note: The safe ampacity is also limited by the temperature rating of the terminals used to connect the wire. Even if the wire is rated for 90°C, the practical limit is often determined by 60°C or 75°C terminals. * Conclusion: The 6 AWG wire is likely capable of carrying between 55A and 75A, depending on the insulation type and termination ratings. Overall current limit and recommendations * The overall maximum continuous discharge current is determined by the weakest link in the system. In this case, the 6 AWG main power cables appear to be the limiting factor, rated for around 55A-75A. * The BMS can handle 400A continuously, and the battery pack can handle 600A continuously. * Therefore, the 6 AWG wire is insufficient for the potential current that the battery and BMS can provide. Recommendations: 3. Upgrade the main power cables: To fully utilize the capacity of the battery and BMS, consider using thicker cables with a higher ampacity rating. Look for cables designed for high-current DC applications, such as Ancor Marine Grade Tinned Cable which uses tinned copper strands for maximum protection against corrosion and fatigue and rated up to 600V. 5. Verify and select cables based on the required continuous current: Determine the maximum continuous current the application requires. Then, choose a cable gauge with an ampacity rating that comfortably exceeds this requirement, taking into account any applicable safety factors. Relevant wire sizing charts and codes (e.g., NFPA 70 or NEC in the US) should be consulted to ensure safety and compliance. 7. Consider temperature and installation:Installation methods and ambient temperatures impact the wire's ampacity, as mentioned previously. Ensure adequate cooling and select appropriate insulation types for operating conditions.Â#nickelcoppersandwich #400antbms #mobiltyscooterbatterybuild So Sound Effects Free Download. Sound Effects Downloader To Help You Download The Highest Quality #nickelcoppersandwich #400antbms #mobiltyscooterbatterybuild So Sound Effects Free Download For TikTok Videos. You Just Search Sound Effects And Download.